起重机钩不旋转固定

Is your crane hook stuck, refusing to swivel smoothly? A crane hook that won’t rotate is more than just an annoyance—it’s a major safety hazard and a significant productivity killer. It can cause load instability, uneven stress on the sling, and even dangerous accidents.

If you’re searching for a fix for a “crane hook not rotating,” you’ve come to the right place. This guide will walk you through the most common causes and provide practical, step-by-step solutions to get your hook moving freely again and ensure safe operation.

Why a Rotating Hook is Crucial for Safety

A freely rotating hook is essential for proper rigging. It allows the load to self-center, prevents slings from twisting and kinking, and ensures the load is balanced. A seized hook forces the wire rope or chain to twist instead, leading to accelerated wear, 损害, and potential failure.

7 Common Reasons Your Crane Hook Won’t Rotate (以及如何修复它们)

1. Lack of Lubrication (The Most Common Cause)

The swivel mechanism (bearings or bushing) inside the hook requires regular lubrication to function smoothly. 随着时间的推移, grease hardens, collects dirt, and washes away, leading to increased friction and eventual seizing.

• Fix: Apply a penetrating oil to help break up rust and debris. Then, thoroughly clean the old grease and apply a fresh, high-quality lubricant recommended by the manufacturer. Always follow the crane’s manual for the correct lubrication type and schedule.

2. Dirt, Debris, and Contamination

Construction and industrial sites are dirty environments. Dust, grit, concrete splatter, and metal filings can work their way into the swivel assembly, acting as an abrasive paste that grinds down components and prevents movement.

• Fix: Regularly clean the hook and its swivel mechanism. Use a wire brush, rag, and compressed air (if available) to remove all visible debris before applying new lubricant.

3. Corrosion and Rust

Exposure to moisture, 雨, or humid conditions can cause the internal components of the swivel to rust and corrode. This bonds the moving parts together, effectively welding them in place.

• Fix: For light surface rust, apply a penetrating oil and work the hook back and forth gently to loosen it. For severe corrosion, the hook may need to be disassembled, cleaned with a rust dissolver, and inspected for damage. If corrosion is extensive, replacement is often safer.

4. Mechanical Damage (Bent Hook or Damaged Swivel)

A direct impact from a dropped load or snagging can physically damage the hook or its swivel assembly. A bent hook or deformed throat will not rotate correctly.

• Fix: Visually inspect the hook for any deformation. Look for twists, bends, or a throat opening that has changed shape. A bent hook is a failed hook. It must be taken out of service and replaced immediately. Do not attempt to straighten it.

5. Overloading and Bearing Failure

Exceeding the Working Load Limit (wll) of the hook can cause catastrophic internal damage. It can crack the hook, collapse the bearing races, or deform internal components, leading to a complete and sudden seizure.

• Fix: Never exceed the rated capacity. If you suspect bearing failure due to overloading, the hook assembly must be replaced. Internal bearing damage is often not repairable in the field.

6. Improper Storage or Lack of Use

A hook that sits idle for long periods, especially outdoors, is prone to seizing up for all the reasons listed above—lubricant dries out, and corrosion sets in.

• Fix: Implement a regular inspection and “exercise” routine for all hooks, even those in storage. Rotate them by hand periodically and apply lubricant as needed.

7. Worn-Out Swivel Bushing or Bearings

Like any mechanical component, the swivel mechanism has a finite lifespan. After years of use, bearings can wear out, become pitted, and lose their ability to turn smoothly.

• Fix: Most hooks are sealed units. While some can be disassembled for bearing replacement, it often requires special tools and expertise. Consult the manufacturer’s guidelines. 在大多数情况下, replacing the entire hook block is the safest and most efficient solution.

首先安全: The Ultimate “Fix”

Your number one priority is safety. Before any repair attempt, follow these steps:

• 1. De-energize the Crane: Lock out and tag out (心) the crane to prevent accidental operation.
• 2. Inspect Thoroughly: Perform a detailed inspection of the hook, looking for wear, 裂缝, 形变, and throat opening increase.
• 3. Know When to Replace: If there is any doubt about the integrity of the hook, REPLACE IT. Hooks are relatively inexpensive compared to the cost of an accident.

预防胜于治愈

The best fix for a “crane hook not rotating” is to prevent it from happening in the first place.

• 1. Establish a Regular Maintenance Schedule: Include cleaning and lubrication of all hooks.
• 2. Perform Daily Visual Inspections: Look for signs of damage, 穿, and lack of rotation before each shift.
• 3. Train Operators and Riggers: Ensure all personnel understand the importance of a rotating hook and how to identify problems.

A non-rotating crane hook is a clear sign that maintenance is overdue or that damage has occurred. By understanding these common causes—from simple lack of lubrication to serious mechanical damage—you can diagnose the issue and apply the correct fix. Remember, when in doubt, always err on the side of caution and consult a qualified crane technician. Keep your hooks moving freely to ensure a safe and efficient worksite.