Колико преокрета је дозвољено у куци за кран?

If you work with cranes, you’ve likely heard the golden rule: “Never side-load or twist a crane hook.” It’s drummed into every operator and rigger during training. But in the complex, real-world environment of a job site, a perfectly straight lift isn’t always possible. A slight twist or lateral force can sometimes seem inevitable.

This leads to a critical safety question: Is any amount of twist acceptable? And if so, how much?

The short, crucial answer is: Under ideal conditions, the allowed twist in a crane hook is zero degrees. The hook, its latch, and the entire lifting system are designed to handle pure vertical tension. Any deviation from this introduces dangerous stress.

Међутим, industry standards acknowledge that minor, unintentional angles can occur. The key is understanding the severe risks and the strict, non-negotiable limits.

Why is Twisting a Hook So Dangerous?

A twisted or side-loaded hook doesn’t just bend; it fails in catastrophic ways. The primary dangers are:

• 1. Unhooking and Load Dropping: The most immediate risk. A twisted hook can cause the load to slip out of the throat, especially if the safety latch is missing, damaged, or forced open. This can happen in an instant.
• 2. Hook Deformation: Excessive side-pull can permanently bend or warp the hook. A deformed hook has compromised its structural integrity and must be removed from service immediately.
• 3. Cracking and Metal Fatigue: Side-loading places extreme tensile and bending stresses on the hook’s material, particularly on the inner radius (the “saddle”) where stress is already concentrated. This can lead to micro-cracks that grow over time, resulting in a sudden, brittle fracture under load.
• 4. Damage to Other Components: The twisting force doesn’t stop at the hook. It travels up the chain, damaging swivels, жичана коноп, sheaves, and even the crane’s boom, leading to expensive repairs and extended downtime.

The Official Standards and Tolerances

Recognizing that a perfectly straight lift isn’t always feasible, leading standards like ASME B30.10 (Куке) provide guidance. They state that hooks are designed for in-line tension.

While they don’t specify a precise “safe angle” for twisting, they are very clear on the consequence: a hook that has been twisted or bent beyond its original shape must be removed from service and destroyed.

The tolerance, therefore, is not for intentional twisting but for minimal, unavoidable misalignment. The general industry consensus and many crane manufacturer manuals stipulate that side-loading should never exceed 3 до 5 degrees from the vertical plane.

This isn’t a “safe” angle but rather a very small tolerance for error. Any visible or planned twist beyond this is a major red flag and must be corrected before proceeding with the lift.

What to Do If You See a Twisted Hook

• 1. STOP THE LIFT: Safety is always the first priority. If you observe a hook under a dangerous side-pull, halt operations immediately.
• 2. Communicate: Inform the crane operator and the signal person about the hazardous condition.
• 3. Correct the Load: Lower the load safely to the ground. Never try to fix a twist while the load is suspended. Re-rig the load to ensure the center of gravity is directly below the hook point, allowing the hoist rope to hang perfectly vertical.
• 4. Inspect the Hook: Once the load is set down, a competent person must perform a thorough inspection of the hook for any signs of deformation, twisting, or cracking. This includes checking the latch and the hook’s opening.
• 5. Remove and Tag Out: If any deformation is found, the hook must be tagged “DO NOT USE” and removed from service. It cannot be straightened or repaired—it must be replaced.

Best Practices to Prevent Twisting

• 1. Proper Rigging: Always ensure the load is correctly rigged with the center of gravity directly below the hook. Use appropriately rated shackles, slings, and spreader bars to keep the load balanced and the hook upright.
• 2. Use a Swivel: For lifts where load rotation is expected or necessary (Нпр., turning a beam), use a certified, load-rated rotating swivel attached between the hook and the top of the rigging. This allows rotation without transferring torque to the hook itself.
• 3. Operator and Rigger Training: Continuous training ensures everyone understands the immense risks of side-loading and knows how to plan and execute a lift correctly.

Don’t think in terms of “how much twist is allowed.” Think instead: “How can I achieve zero twist?”

There is no safe amount of intentional twist. Тхе 3-5 degree leeway is a buffer for imperfection, not a license to cut corners. A twisted hook is a hook on the verge of failure. Respect the design limits of your equipment, prioritize meticulous rigging, and never hesitate to stop a lift that looks unsafe. The integrity of your hook is quite literally the linchpin of your entire operation.